1、玻璃鋼水箱在安裝前首先要檢查水箱混凝土基礎表面是否平整，然后按照水箱底板尺寸，將已經截好的槽鋼進行焊接組合，然后開始組裝水箱板，水箱板與水箱板之間中間夾密封條，以螺栓連接。先將底板組裝完畢平鋪到槽鋼底座上，然后將側面組合與底部連接。

2、連接完畢后，開始安裝拉筋，首先在玻璃鋼水箱四塊側板的十字結合點處安裝拉筋板，在四塊板靠角處鉆好孔，用四根對絲，穿過內外拉筋板，把四塊板夾緊，螺桿與板之間要夾膠墊密封，把拉筋帶螺紋的兩端穿過拉筋板中間孔，用螺母將兩塊內拉筋板拉緊。玻璃鋼水箱還有專 門的堵漏原件，它主要用于底板和下側板四塊板結合處的菱形孔洞及側板四角中間結合處的菱形空洞密封，在外緊固并且由內向外穿。

3、我們在運輸玻璃鋼水箱時，要先打木箱板，為了防止其劃擦、擠壓，每塊板材之間要用塑料泡沫進行包裹，包裝水箱由于是“泡貨”，在運輸吊裝時要注意不得碰撞，以防變形，使焊縫開裂，嚴禁重力敲打，萬一出現差錯，現場很難修復，管道連接處水箱內應襯以加強板保護，提高接頭強度。箱體寬度、高度設計，應考慮公路、隧道、橋涵等汽車運輸所允許的技術規范。水箱在運輸途中需對其進行加固，防止其在車廂內滑動對水箱板造成損壞。